- 您現在的位置：買賣IC網 > PDF目錄363893 > W6691 (WINBOND ELECTRONICS CORP) ISDN S/T Interface Transceiver PDF資料下載
參數資料
| 型號： | W6691 |
| 廠商： | WINBOND ELECTRONICS CORP |
| 英文描述： | ISDN S/T Interface Transceiver |
| 中文描述： | 綜合業務數字網的S / T接口收發器 |
| 文件頁數： | 88/106頁 |
| 文件大小： | 428K |
| 代理商： | W6691 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁當前第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁
Preliminary W6691
Publication Release Date: Sep 2001
88 Revision 1.1
When the number of empty locations is equal to or greater than the threshold value, a XFR interrupt is
generated. After a XFR interrupt, up to 64 or 96 bytes of data can be written into this FIFO for transmission.
8.11.3 B1_ch command register
B1_CMDR
Read/Write
Address 53H
Value after reset: 00H
7
6
5
0
4
0
3
0
2
1
0
RACK
RRST
XMS
XME
XRST
RACK Receive Message Acknowledge
After a RMR or RME interrupt, the microprocessor reads out the data in B1_RFIFO, it then sets this bit to
explicitly acknowledge the interrupt.
This bit is write only. It's auto-clear. Writing “0” to this bit has no effect. If RACK bit is set to “1” for operating
“Receiver Acknowledge”, It is not necessary to reset RACK bit to “0” by host processor. That is to say, once
RACK is set to “1”, RACK bit is reset to “0” by W6691 automatically.
RRST Receiver Reset
Setting this bit resets the B1_ch HDLC receiver.
This bit is write-only. It's auto-clear. Writing “0” to this bit has no effect. If RRST bit is set to “1” for operating
“Receiver Reset”, It is not necessary to reset RRST bit to “0” by host processor. That is to say, once RRST is
set to “1”, RRST bit is reset to “0” by W6691 automatically.
XMS Transmit Message Start/Continue
In transparent mode, setting this bit initiates the transparent transmission of B1_XFIFO data. The opening flag
is automatically added to the message by the B1_ch HDLC controller. Zero bit insertion is performed on the
data. This bit is also used in subsequent transmission of the frame.
In extended transparent mode, settint this bit activates the transmission of B1_XFIFO data. No flag, CRC or
zero bit insertion is added on the data.
This bit is write-only. It's auto-clear. Writing “0” to this bit has no effect. If XMS bit is set to “1” for operating
“Transmit Message Start/Continue”, It is not necessary to reset XMS bit to “0” by host processor. That is to
say, once XMS is set to “1”, XMS bit is reset to “0” by W6691 automatically.
XME Transmit Message End
In transparent mode, setting this bit indicates the end of the whole frame transmission. The B1_ch HDLC
controller transmits the data in FIFO and automatically appends the CRC and the closing flag sequence in
transparent mode.
相關PDF資料 |
PDF描述 |
|---|---|
| W6691CD | ISDN S/T Interface Transceiver |
| W6691CP | ISDN S/T Interface Transceiver |
| W6692 | PCI Bus ISDN S/T Interface Controller(PCI總線的ISDN S/T接口控制器) |
| W6693A | USB Bus ISDN S/T Interface Controller(USB總線的ISDN S/T接口控制器) |
| W6694 | PCI Bus ISDN S/T Interface Controller(PCI總線的ISDN S/T接口控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W66910 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| W66910CD | 制造商:WINBOND 制造商全稱:Winbond 功能描述:TE Mode ISDN S/T-Controller with Microprocessor Interface |
| W6691CD | 制造商:WINBOND 制造商全稱:Winbond 功能描述:ISDN S/T Interface Transceiver |
| W6691CP | 制造商:WINBOND 制造商全稱:Winbond 功能描述:ISDN S/T Interface Transceiver |
| W6692 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:PCI Bus ISDN S/T-Controller |
發布緊急采購，3分鐘左右您將得到回復。