国产精品成人VA在线观看-国产乱妇乱子视频在播放-国产日韩精品一区二区三区在线-国模精品一区二区三区

參數資料
型號: W77C32
廠商: WINBOND ELECTRONICS CORP
元件分類: 8位微控制器
英文描述: 8 BIT MICROCONTROLLER
中文描述: 8位微控制器
文件頁數: 14/71頁
文件大小: 860K
代理商: W77C32
Preliminary W77C32
- 14 -
XT/RGRG: Crystal/RC Oscillator Select. Setting this bit selects crystal or external clock as system
clock source. Clearing this bit selects the on-chip RC oscillator as clock source.
XTUP(STATUS.4) must be set to 1 and XTOFF (PMR.3) must be cleared before this bit can
be set. Attempts to set this bit without obeying these conditions will be ignored. This bit is set
to 1 after a power-on reset and unchanged by other forms of reset.
RGMD: RC Mode Status. This bit indicates the current clock source of microcontroller. When cleared,
CPU is operating from the external crystal or oscillator. When set, CPU is operating from the
on-chip RC oscillator. This bit is cleared to 0 after a power-on reset and unchanged by other
forms of reset.
RGSL: RC Oscillator Select. This bit selects the clock source following a resume from Power Down
Mode. Setting this bit allows device operating from RC oscillator when a resume from Power
Down Mode. When this bit is cleared, the device will hold operation until the crystal oscillator
has warmed-up following a resume from Power Down Mode. This bit is cleared to 0 after a
power-on reset and unchanged by other forms of reset.
Serial Port Control
Bit:
7
6
5
4
3
2
1
0
SM0/FE
SM1
SM2
REN
TB8
RB8
TI
RI
Mnemonic: SCON
Address: 98h
SM0/FE: Serial port 0, Mode 0 bit or Framing Error Flag: The SMOD0 bit in PCON SFR determines
whether this bit acts as SM0 or as FE. The operation of SM0 is described below. When used
as FE, this bit will be set to indicate an invalid stop bit. This bit must be manually cleared in
software to clear the FE condition.
SM1:
Serial port Mode bit 1:
SM0 SM1 Mode
Description
0
0
0
Synchronous
0
1
1
Asynchronous 10
1
0
2
Asynchronous 11
1
1
3
Asynchronous 11
Length
8
Baud rate
4/12 Tclk
variable
64/32 Tclk
variable
SM2:
Multiple processors communication. Setting this bit to 1 enables the multiprocessor
communication feature in mode 2 and 3. In mode 2 or 3, if SM2 is set to 1, then RI will not be
activated if the received 9th data bit (RB8) is 0. In mode 1, if SM2 = 1, then RI will not be
activated if a valid stop bit was not received. In mode 0, the SM2 bit controls the serial port
clock. If set to 0, then the serial port runs at a divide by 12 clock of the oscillator. This gives
compatibility with the standard 8052. When set to 1, the serial clock become divide by 4 of
the oscillator clock. This results in faster synchronous serial communication.
Receive enable: When set to 1 serial reception is enabled, otherwise reception is
disabled.
This is the 9th bit to be transmitted in modes 2 and 3. This bit is set and cleared by software
as desired.
In modes 2 and 3 this is the received 9th data bit. In mode 1, if SM2 = 0, RB8 is the stop bit
that was received. In mode 0 it has no function.
Transmit interrupt flag: This flag is set by hardware at the end of the 8th bit time in mode 0, or
at the beginning of the stop bit in all other modes during serial transmission. This bit must be
cleared by software.
REN:
TB8:
RB8:
TI:
相關PDF資料
PDF描述
W77C58 8 BIT MICROCONTROLLER
W77E058A40DL 8-BIT MICROCONTROLLER
W77E058A40FL 8-BIT MICROCONTROLLER
W77E058A40PL 8-BIT MICROCONTROLLER
W77E058A 8-BIT MICROCONTROLLER
相關代理商/技術參數
參數描述
W77C32_07 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MICROCONTROLLER
W77C32-25 制造商:WINBOND 制造商全稱:Winbond 功能描述:8 BIT MICROCONTROLLER
W77C32-40 制造商:WINBOND 制造商全稱:Winbond 功能描述:8 BIT MICROCONTROLLER
W77C32F-25 制造商:WINBOND 制造商全稱:Winbond 功能描述:8 BIT MICROCONTROLLER
W77C32F-40 制造商:WINBOND 制造商全稱:Winbond 功能描述:8 BIT MICROCONTROLLER