- 您現在的位置：買賣IC網 > PDF目錄363895 > W77LE532 (WINBOND ELECTRONICS CORP) 8 BIT MICROCONTROLLER PDF資料下載
參數資料
| 型號： | W77LE532 |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | 8位微控制器 |
| 英文描述： | 8 BIT MICROCONTROLLER |
| 中文描述： | 8位微控制器 |
| 文件頁數： | 27/85頁 |
| 文件大小： | 2458K |
| 代理商： | W77LE532 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁
Preliminary W77LE532
Publication Release Date: May 14, 2003
- 27 - Revision A1
CD1,
CD0
Clocks/machine Cycle
0
0
Reserved
0
1
4
1
0
64
1
1
1024
SWB:
Switchback Enable. Setting this bit allows an enabled external interrupt or serial port activity
to force the CD1,CD0 to divide by 4 state (0,1). The device will switch modes at the start of
the jump to interrupt service routine while a external interrupt is enabled and actually
recongnized by microcontroller. While a serial port reception, the switchback occurs at the
start of the instruction following the falling edge of the start bit.
ALE0FF: This bit disables the expression of the ALE signal on the device pin during all on-board
program and data memory accesses. External memory accesses will automatically enable
ALE independent of ALEOFF.
0 = ALE expression is enable; 1 = ALE expression is disable
DME0: This bit determines the on-chip MOVX SRAM to be enabled or disabled. Set this bit to 1 will
enable the on-chip 1KB MOVX SRAM.
STATUS REGISTER
Bit:
7
6
5
4
3
2
1
0
-
HIP
LIP
XTUP
SPTA1
SPRA1
SPTA0
SPRA0
Mnemonic: STATUS
Address: C5h
HIP: High Priority Interrupt Status. When set, it indicates that software is servicing a high priority
interrupt. This bit will be cleared when the program executes the corresponding RETI
instruction.
LIP: Low Priority Interrupt Status. When set, it indicates that software is servicing a low priority
interrupt. This bit will be cleared when the program executes the corresponding RETI
instruction.
XTUP: Crystal Oscillator Warm-up Status. when set, this bit indicates CPU has detected clock to be
ready. Each time the crystal oscillator is restarted by exit from power down mode, hardware
will clear this bit. This bit is set to 1 after a power-on reset.
SPTA1: Serial Port 1 Transmit Activity. This bit is set during serial port 1 is currently transmitting data.
It is cleared when TI_1 bit is set by hardware. Changing the Clock Divide Control bits
CD0, CD1 will be ignored when this bit is set to 1 and SWB = 1.
SPRA1: Serial Port 1 Receive Activity. This bit is set during serial port 1 is currently receiving a data. It
is cleared when RI_1 bit is set by hardware. Changing the Clock Divide Control bits CD0,
CD1
will be ignored when this bit is set to 1 and SWB = 1.
SPTA0: Serial Port 0 Transmit Activity. This bit is set during serial port 0 is currently transmitting data.
It is cleared when TI bit is set by hardware. Changing the Clock Divide Control bits CD0, CD1
will be ignored when this bit is set to 1 and SWB = 1.
相關PDF資料 |
PDF描述 |
|---|---|
| W77LE58 | 8 BIT MICROCONTROLLER |
| W77LE58-25 | 8 BIT MICROCONTROLLER |
| W77LE58F-25 | 8 BIT MICROCONTROLLER |
| W77LE58P-25 | 8 BIT MICROCONTROLLER |
| W78151 | 8-BIT Microcontroller(8位的微控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W77LE532_07 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MICROCONTROLLER |
| W77LE58 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8 BIT MICROCONTROLLER |
| W77LE58_07 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MICROCONTROLLER |
| W77LE58-25 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8 BIT MICROCONTROLLER |
| W77LE58F-25 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8 BIT MICROCONTROLLER |
發布緊急采購，3分鐘左右您將得到回復。