- 您現在的位置：買賣IC網 > PDF目錄363895 > W77E58-25 (WINBOND ELECTRONICS CORP) 8 BIT MICROCONTROLLER PDF資料下載
參數資料
| 型號： | W77E58-25 |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8 BIT MICROCONTROLLER |
| 中文描述： | 8-BIT, FLASH, 25 MHz, MICROCONTROLLER, PDIP40 |
| 封裝： | DIP-40 |
| 文件頁數： | 53/85頁 |
| 文件大小： | 570K |
| 代理商： | W77E58-25 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁當前第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁
Preliminary W77E58
Publication Release Date: March 1999
- 53 - Revision A1
Execution continues from the vectored address till an RETI instruction is executed. On execution of
the RETI instruction the processor pops the Stack and loads the PC with the contents at the top of the
stack. The user must take care that the status of the stack is restored to what is was after the
hardware LCALL, if the execution is to return to the interrupted program. The processor does not
notice anything if the stack contents are modified and will proceed with execution from the address
put back into PC. Note that a RET instruction would perform exactly the same process as a RETI
instruction, but it would not inform the Interrupt Controller that the interrupt service routine is
completed, and would leave the controller still thinking that the service routine is underway.
Interrupt Response Time
The response time for each interrupt source depends on several factors, such as the nature of the
interrupt and the instruction underway. In the case of external interrupts INT0 to INT5 , they are
sampled at C3 of every machine cycle and then their corresponding interrupt flags IEx will be set or
reset. The Timer 0 and 1 overflow flags are set at C3 of the machine cycle in which overflow has
occurred. These flag values are polled only in the next machine cycle. If a request is active and all
three conditions are met, then the hardware generated LCALL is executed. This LCALL itself takes
four machine cycles to be completed. Thus there is a minimum time of five machine cycles between
the interrupt flag being set and the interrupt service routine being executed.
A longer response time should be anticipated if any of the three conditions are not met. If a higher or
equal priority is being serviced, then the interrupt latency time obviously depends on the nature of the
service routine currently being executed. If the polling cycle is not the last machine cycle of the
instruction being executed, then an additional delay is introduced. The maximum response time (if no
other interrupt is in service) occurs if the W77E58 is performing a write to IE, IP, EIE or EIP and then
executes a MUL or DIV instruction. From the time an interrupt source is activated, the longest
reaction time is 12 machine cycles. This includes 1 machine cycle to detect the interrupt, 2 machine
cycles to complete the IE, IP, EIE or EIP access, 5 machine cycles to complete the MUL or DIV
instruction and 4 machine cycles to complete the hardware LCALL to the interrupt vector location.
Thus in a single-interrupt system the interrupt response time will always be more than 5 machine
cycles and not more than 12 machine cycles. The maximum latency of 12 machine cycle is 48 clock
cycles. Note that in the standard 8051 the maximum latency is 8 machine cycles which equals 96
machine cycles. This is a 50% reduction in terms of clock periods.
PROGRAMMABLE TIMERS/COUNTERS
The W77E58 has three 16-bit programmable timer/counters and one programmable Watchdog timer.
The Watchdog timer is operationally quite different from the other two timers.
TIMER/COUNTERS 0 & 1
The W77E58 has two 16-bit Timer/Counters. Each of these Timer/Counters has two 8 bit registers
which form the 16 bit counting register. For Timer/Counter 0 they are TH0, the upper 8 bits register,
and TL0, the lower 8 bit register. Similarly Timer/Counter 1 has two 8 bit registers, TH1 and TL1. The
two can be configured to operate either as timers, counting machine cycles or as counters counting
external inputs.
相關PDF資料 |
PDF描述 |
|---|---|
| W77E58-40 | 8 BIT MICROCONTROLLER |
| W77E58F-25 | 8 BIT MICROCONTROLLER |
| W77E58F-40 | 8 BIT MICROCONTROLLER |
| W77E58P-25 | 8 BIT MICROCONTROLLER |
| W77E58P-40 | 8 BIT MICROCONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W77E58-40 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8 BIT MICROCONTROLLER |
| W77E58F-25 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8 BIT MICROCONTROLLER |
| W77E58F-40 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8 BIT MICROCONTROLLER |
| W77E58P-25 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8 BIT MICROCONTROLLER |
| W77E58P-40 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8 BIT MICROCONTROLLER |
發布緊急采購，3分鐘左右您將得到回復。