- 您現在的位置：買賣IC網 > PDF目錄363895 > W77E516 (WINBOND ELECTRONICS CORP) 8-BIT MICROCONTROLLER PDF資料下載
參數資料
| 型號： | W77E516 |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | 8位微控制器 |
| 英文描述： | 8-BIT MICROCONTROLLER |
| 中文描述： | 8位微控制器 |
| 文件頁數： | 65/85頁 |
| 文件大小： | 596K |
| 代理商： | W77E516 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁當前第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁
Preliminary W77E516
Publication Release Date: August 16, 2002
- 65 -
Revision A1
The functional block diagram is shown below. Data enters and leaves the Serial port on the RxD
line. The TxD line is used to output the shift clock. The shift clock is used to shift data into and out
of the W77E516 and the device at the other end of the line. Any instruction that causes a write to
SBUF will start the transmission. The shift clock will be activated and data will be shifted out on the
RxD pin till all 8 bits are transmitted. If SM2 = 1, then the data on RxD will appear 1 clock period
before the falling edge of shift clock on TxD. The clock on TxD then remains low for 2 clock
periods, and then goes high again. If SM2 = 0, the data on RxD will appear 3 clock periods before
the falling edge of shift clock on TxD. The clock on TxD then remains low for 6 clock periods, and
then goes high again. This ensures that at the receiving end the data on RxD line can either be
clocked on the rising edge of the shift clock on TxD or latched when the TxD clock is low.
SBUF
Transmit Shift Register
Receive Shift Register
TX
SHIFT
PAROUT
Internal
Data Bus
Internal
Data Bus
RXD
P3.0 Alternate
Output Function
TXD
P3.1 Alternate
Output function
RXD
P3.0 Alternate
Iutput function
Serial Port Interrupt
Write to
SBUF
TX
START
SOUT
TI
RI
REN
PARIN
LOAD
CLOCK
Read SBUF
SBUF
TX CLOCK
RI
SERIAL
CONTROLLER
SHIFT
CLOCK
RX
CLOCK
LOAD SBUF
RX
START
RX SHIFT
CLOCK
SIN
÷
4
÷
12
1
0
SM2
Clock Source
Mode input
div. by 4 osc/1
div. by 64 osc/16
div. by 1024 osc/256
Figure 20. Serial Port Mode 0
The TI flag is set high in C1 following the end of transmission of the last bit. The serial port will
receive data when REN is 1 and RI is zero. The shift clock (TxD) will be activated and the serial port
will latch data on the rising edge of shift clock. The external device should therefore present data on
the falling edge on the shift clock. This process continues till all the 8 bits have been received.
The RI flag is set in C1 following the last rising edge of the shift clock on TxD. This will stop
reception, till the RI is cleared by software.
Mode 1
In Mode 1, the full duplex asynchronous mode is used. Serial communication frames are made up
of 10 bits transmitted on TXD and received on RXD. The 10 bits consist of a start bit (0), 8 data bits
(LSB first), and a stop bit (1). On receive, the stop bit goes into RB8 in the SFR SCON. The baud
rate in this mode is variable. The serial baud can be programmed to be 1/16 or 1/32 of the Timer 1
overflow. Since the Timer 1 can be set to different reload values, a wide variation in baud rates is
possible.
Transmission begins with a write to SBUF. The serial data is brought out on to TxD pin at C1
following the first roll-over of divide by 16 counter. The next bit is placed on TxD pin at C1 following
the next rollover of the divide by 16 counter. Thus the transmission is synchronized to the divide by
16 counter and not directly to the write to SBUF signal. After all 8 bits of data are transmitted, the
相關PDF資料 |
PDF描述 |
|---|---|
| W77E516-25 | 8-BIT MICROCONTROLLER |
| W77E516-40 | 8-BIT MICROCONTROLLER |
| W77E516F-25 | 8-BIT MICROCONTROLLER |
| W77E516F-40 | 8-BIT MICROCONTROLLER |
| W77E516P-25 | 8-BIT MICROCONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W77E516-25 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MICROCONTROLLER |
| W77E516-40 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MICROCONTROLLER |
| W77E516A | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MICROCONTROLLER |
| W77E516A40DL | 功能描述:IC MCU 8-BIT 64K FLASH 40-DIP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:W77 標準包裝:250 系列:80C 核心處理器:8051 芯體尺寸:8-位 速度:16MHz 連通性:EBI/EMI，I²C，UART/USART 外圍設備:POR，PWM，WDT 輸入/輸出數:40 程序存儲器容量:- 程序存儲器類型:ROMless EEPROM 大小:- RAM 容量:256 x 8 電壓 - 電源 (Vcc/Vdd):4.5 V ~ 5.5 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-LCC（J 形引線） 包裝:帶卷 (TR) |
| W77E516A40FL | 功能描述:IC MCU 8-BIT 64K FLASH 44-QFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:W77 標準包裝:250 系列:80C 核心處理器:8051 芯體尺寸:8-位 速度:16MHz 連通性:EBI/EMI，I²C，UART/USART 外圍設備:POR，PWM，WDT 輸入/輸出數:40 程序存儲器容量:- 程序存儲器類型:ROMless EEPROM 大小:- RAM 容量:256 x 8 電壓 - 電源 (Vcc/Vdd):4.5 V ~ 5.5 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-LCC（J 形引線） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。