- 您現在的位置：買賣IC網 > PDF目錄375845 > FM24C256-SE (Electronic Theatre Controls, Inc.) 256Kb FRAM Serial Memory PDF資料下載
參數資料
| 型號： | FM24C256-SE |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | 256Kb FRAM Serial Memory |
| 中文描述： | 的256Kb FRAM的串行存儲器 |
| 文件頁數： | 4/13頁 |
| 文件大小： | 115K |
| 代理商： | FM24C256-SE |
FM24C256
Rev 1.3
Feb. 2004
Page 4 of 13
Stop
(Master)
Start
(Master)
7
Data bits
(Transmitter)
6
0
Data bit
(Transmitter)
Acknowledge
(Receiver)
Figure 3. Data Transfer Protocol
Stop Condition
A Stop condition is indicated when the bus master
drives SDA from low to high while the SCL signal is
high. All operations using the FM24C256 must end
with a Stop condition. If an operation is pending
when a Stop is asserted, the operation will be aborted.
The master must have control of SDA (not a memory
read) in order to assert a Stop condition.
Start Condition
A Start condition is indicated when the bus master
drives SDA from high to low while the SCL signal is
high. All read and write transactions begin with a
Start condition. An operation in progress can be
aborted by asserting a Start condition at any time.
Aborting an operation using the Start condition will
ready the FM24C256 for a new operation.
If during operation the power supply drops below the
specified VDD minimum, the system should issue a
Start condition prior to performing another operation.
Data/Address Transfer
All data transfers (including addresses) take place
while the SCL signal is high. Except under the two
conditions described above, the SDA signal should
not change while SCL is high.
Acknowledge
The Acknowledge takes place after the 8
th
data bit
has been transferred in any transaction. During this
state the transmitter should release the SDA bus to
allow the receiver to drive it. The receiver drives the
SDA signal low to acknowledge receipt of the byte.
If the receiver does not drive SDA low, the condition
is a No-Acknowledge and the operation is aborted.
The receiver would fail to acknowledge for two
distinct reasons. First is that a byte transfer fails. In
this case, the No-Acknowledge ends the current
operation so that the part can be addressed again.
This allows the last byte to be recovered in the event
of a communication error.
Second and most common, the receiver does not
acknowledge to deliberately end an operation. For
example, during a read operation, the FM24C256
will continue to place data onto the bus as long as
the receiver sends Acknowledges (and clocks).
When a read operation is complete and no more data
is needed, the receiver must not acknowledge the
last byte. If the receiver acknowledges the last byte,
this will cause the FM24C256 to attempt to drive
the bus on the next clock while the master is sending
a new command such as Stop.
Slave Address
The first byte that the FM24C256 expects after a
Start condition is the slave address. As shown in
Figure 4, the slave address contains the Slave ID
(device type), the device select address bits, and a
bit that specifies if the transaction is a read or a
write. Bits 7-4 define the device type and must be
set to 1010b for the FM24C256. These bits allow
other types of function types to reside on the 2-wire
bus within an identical address range. Bits 3-1 are
the device select bits which are equivalent to chip
select bits. They must match the corresponding
value on the external address pins to select the
device. Up to eight FM24C256 devices can reside
on the same two-wire bus by assigning a different
address to each. Bit 0 is the read/write bit. A 1
indicates a read operation, and a 0 indicates a write.
1
0
1
0
A2
A1
A0 R/W
Slave
ID
Device
Select
7
6
5
4
3
2
1
0
Figure 4. Slave Address
相關PDF資料 |
PDF描述 |
|---|---|
| FM24C256LZYYX | 256 KBit 2-Wire Bus Interface Serial EEPROM with Write Protect |
| FM24C256FLZYYX | 256 KBit 2-Wire Bus Interface Serial EEPROM with Write Protect |
| FM24C256 | 256K-Bit 2-Wire Bus Interface Serial EEPROM with Write Protect(帶寫保護的256K位的兩線控制總線接口串行EEPROM) |
| FM24C256LZEYYX | 256 KBit 2-Wire Bus Interface Serial EEPROM with Write Protect |
| FM24C256FLZEYYX | 256 KBit 2-Wire Bus Interface Serial EEPROM with Write Protect |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FM24C256-SETR | 功能描述:F-RAM 256K (32Kx8) 5V RoHS:否 存儲容量:512 Kbit 組織:64 K x 8 接口:SPI 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube 制造商:Cypress Semiconductor |
| FM24C256VM8 | 功能描述:電可擦除可編程只讀存儲器 SOIC-8 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| FM24C256VM8X | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:I2C Serial EEPROM |
| FM24C256VN | 功能描述:電可擦除可編程只讀存儲器 DIP-8 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| FM24C256YYX | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:256 KBit 2-Wire Bus Interface Serial EEPROM with Write Protect |
發布緊急采購，3分鐘左右您將得到回復。