- 您現在的位置：買賣IC網 > PDF目錄363895 > W77E58 (WINBOND ELECTRONICS CORP) 8 BIT MICROCONTROLLER PDF資料下載
參數資料
| 型號： | W77E58 |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | 8位微控制器 |
| 英文描述： | 8 BIT MICROCONTROLLER |
| 中文描述： | 8位微控制器 |
| 文件頁數： | 48/85頁 |
| 文件大小： | 570K |
| 代理商： | W77E58 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁當前第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁
Preliminary W77E58
- 48 -
The W77E58 can be woken from the Power Down mode by forcing an external interrupt pin activated,
provided the corresponding interrupt is enabled, while the global enable(EA) bit is set and the external
input has been set to a level detect mode. If these conditions are met, then the low level on the
external pin re-starts the oscillator. Then device executes the interrupt service routine for the
corresponding external interrupt. After the interrupt service routine is completed, the program
execution returns to the instruction after the one which put the device into Power Down mode and
continues from there. When RGSL(EXIF.1) bit is set to 1, the CPU will use the internal RC oscillator
instead of crystal to exit Power Down mode. The microcontroller will automatically switch from RC
oscillator to crystal after clock is stable. The RC oscillator runs at approximately 2
4 MHz. Using RC
oscillator to exit from Power Down mode saves the time for waiting crystal start-up. It is useful in the
low power system which usually be awakened from a short operation then returns to Power Down
mode.
Table 5. Status of external pins during Idle and Power Down
Mode
Program
Memory
ALE
PSEN
PORT0
PORT1
PORT2
PORT3
Idle
Internal
1
1
Data
Data
Data
Data
Idle
External
1
1
Float
Data
Address
Data
Power Down
Internal
0
0
Data
Data
Data
Data
Power Down
External
0
0
Float
Data
Data
Data
RESET CONDITIONS
The user has several hardware related options for placing the W77E58 into reset condition. In
general, most register bits go to their reset value irrespective of the reset condition, but there are a
few flags whose state depends on the source of reset. The user can use these flags to determine the
cause of reset using software. There are two ways of putting the device into reset state. They are
External reset and Watchdog reset.
External Reset
The device continuously samples the RST pin at state C4 of every machine cycle. Therefore the RST
pin must be held for at least 2 machine cycles to ensure detection of a valid RST high. The reset
circuitry then synchronously applies the internal reset signal. Thus the reset is a synchronous
operation and requires the clock to be running to cause an external reset.
Once the device is in reset condition, it will remain so as long as RST is 1. Even after RST is
deactivated, the device will continue to be in reset state for up to two machine cycles, and then begin
program execution from 0000h. There is no flag associated with the external reset condition. However
since the other two reset sources have flags, the external reset can be considered as the default reset
if those two flags are cleared.
相關PDF資料 |
PDF描述 |
|---|---|
| W77E58-25 | 8 BIT MICROCONTROLLER |
| W77E58-40 | 8 BIT MICROCONTROLLER |
| W77E58F-25 | 8 BIT MICROCONTROLLER |
| W77E58F-40 | 8 BIT MICROCONTROLLER |
| W77E58P-25 | 8 BIT MICROCONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W77E58-25 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8 BIT MICROCONTROLLER |
| W77E58-40 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8 BIT MICROCONTROLLER |
| W77E58F-25 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8 BIT MICROCONTROLLER |
| W77E58F-40 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8 BIT MICROCONTROLLER |
| W77E58P-25 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8 BIT MICROCONTROLLER |
發布緊急采購，3分鐘左右您將得到回復。