- 您現在的位置：買賣IC網 > PDF目錄363895 > W77E058A (WINBOND ELECTRONICS CORP) 8-BIT MICROCONTROLLER PDF資料下載
參數資料
| 型號： | W77E058A |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | 8位微控制器 |
| 英文描述： | 8-BIT MICROCONTROLLER |
| 中文描述： | 8位微控制器 |
| 文件頁數： | 45/87頁 |
| 文件大小： | 594K |
| 代理商： | W77E058A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁當前第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁
W77E058A
Publication Release Date: April 17, 2007
- 45 -
Revision A10
The selection of instruction rate is going to take effect after a delay of one instruction cycle. Switching
to divide by 64 or 1024 mode must first go from divide by 4 mode. This means software can not switch
directly between clock/64 and clock/1024 mode. The CPU has to return clock/4 mode first, then go to
clock/64 or clock/1024 mode.
The W77E058 allows the user to use internal RC oscillator instead of external crystal. Setting the
XT/
RG
bit (EXIF.3) selects the crystal or RC oscillator as the clock source. When invoking RC
oscillator in Economy mode, software may set the XTOFF bit to turn off the crystal amplifier for saving
power. The CPU would run at the clock rate of approximately 2
4 MHz divided by 4, 64 or 1024. The
RC oscillator is not precise so that can not be invoked to the operation which needs the accurate time-
base such as serial communication. The RGMD(EXIF.2) indicates current clock source. When
switching the clock source, CPU needs one instruction cycle delay to take effect new setting. If crystal
amplifier is disabled and RC oscillator is present clock source, software must first clear the XTOFF bit
to turn on crystal amplifier before switch to crystal operation. Hardware will set the XTUP bit
(STATUS.4) once the crystal is warm-up and ready for use. It is unable to set XT/
RG
bit to 1 if XTUP
= 0.
In Economy mode, the serial port can not receive/transmit data correctly because the baud rate is
changed. In some systems, the external interrupts may require the fastest process such that the
reducing of operating speed is restricted. In order to solve these dilemmas, the W77E058 offers a
switchback feature which allows the CPU back to clock/4 mode immediately when triggered by serial
operation or external interrupts. The switchback feature is enabled by setting the SWB bit (PMR.5). A
serial port reception/transmission or qualified external interrupt which is enabled and acknowledged
without block conditions will cause CPU to return to divide by 4 mode. For the serial port reception, a
switchback is generated by a falling edge associated with start bit if the serial port reception is
enabled. When a serial port transmission, an instruction which writes a byte of data to serial port
buffer will cause a switchback to ensure the correct transmission. The switchback feature is
unaffected by serial port interrupt flags. After a switchback is generated, the software can manually
return the CPU to Economy mode. Note that the modification of clock control bits CD0 and CD1 will be
ignored during serial port transmit/receive when switchback is enabled. The Watchdog timer reset,
power-on/fail reset or external reset will force the CPU to return to divide by 4 mode.
9.3 Power Down Mode
The device can be put into Power Down mode by writing 1 to bit PCON.1. The instruction that does
this will be the last instruction to be executed before the device goes into Power Down mode. In the
Power Down mode, all the clocks are stopped and the device comes to a halt. All activity is completely
stopped and the power consumption is reduced to the lowest possible value. In this state the ALE and
PSEN
pins are pulled low. The port pins output the values held by their respective SFRs.
The W77E058 will exit the Power Down mode with a reset or by an external interrupt pin enabled as
either level or edge detect. An external reset can be used to exit the Power down state. The high on
RST pin terminates the Power Down mode, and restarts the clock. The program execution will restart
from 0000h. In the Power down mode, the clock is stopped, so the Watchdog timer cannot be used to
provide the reset to exit Power down mode.
The W77E058 can be woken from the Power Down mode by forcing an external interrupt pin
activated, provided the corresponding interrupt is enabled, while the global enable(EA) bit is set. If
these conditions are met, then the low level on the external pin re-starts the oscillator. Then device
executes the interrupt service routine for the corresponding external interrupt. After the interrupt
service routine is completed, the program execution returns to the instruction after the one which put
相關PDF資料 |
PDF描述 |
|---|---|
| W77E468F-25 | 8 BIT MICROCONTROLLER |
| W77E468F-40 | 8 BIT MICROCONTROLLER |
| W77E468 | 8 BIT MICROCONTROLLER |
| W77E516 | 8-BIT MICROCONTROLLER |
| W77E516-25 | 8-BIT MICROCONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W77E058A40DL | 功能描述:IC MCU 8-BIT 32K FLASH 40-DIP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:W77 標準包裝:250 系列:80C 核心處理器:8051 芯體尺寸:8-位 速度:16MHz 連通性:EBI/EMI，I²C，UART/USART 外圍設備:POR，PWM，WDT 輸入/輸出數:40 程序存儲器容量:- 程序存儲器類型:ROMless EEPROM 大小:- RAM 容量:256 x 8 電壓 - 電源 (Vcc/Vdd):4.5 V ~ 5.5 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-LCC（J 形引線） 包裝:帶卷 (TR) |
| W77E058A40FL | 功能描述:IC MCU 8-BIT 32K FLASH 44-PQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:W77 標準包裝:250 系列:80C 核心處理器:8051 芯體尺寸:8-位 速度:16MHz 連通性:EBI/EMI，I²C，UART/USART 外圍設備:POR，PWM，WDT 輸入/輸出數:40 程序存儲器容量:- 程序存儲器類型:ROMless EEPROM 大小:- RAM 容量:256 x 8 電壓 - 電源 (Vcc/Vdd):4.5 V ~ 5.5 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-LCC（J 形引線） 包裝:帶卷 (TR) |
| W77E058A40PL | 功能描述:IC MCU 8-BIT 32K FLASH 44-PLCC RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:W77 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN，SCI，SPI 外圍設備:POR，PWM，溫度傳感器，WDT 輸入/輸出數:21 程序存儲器容量:40KB（20K x 16） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323 |
| W77E11 | 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:EXECUTION EX. NO.1 DX CODE ZA |
| W77E468 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8 BIT MICROCONTROLLER |
發布緊急采購，3分鐘左右您將得到回復。