- 您現在的位置：買賣IC網 > PDF目錄363889 > W49V002FAP (WINBOND ELECTRONICS CORP) 256K X 8 CMOS FLASH MEMORY WITH FWH INTERFACE PDF資料下載
參數資料
| 型號： | W49V002FAP |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | PROM |
| 英文描述： | 256K X 8 CMOS FLASH MEMORY WITH FWH INTERFACE |
| 中文描述： | 256K X 8 FLASH 3.3V PROM, 11 ns, PQCC32 |
| 封裝： | PLASTIC, LCC-32 |
| 文件頁數： | 3/32頁 |
| 文件大?。?/td> | 300K |
| 代理商： | W49V002FAP |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
W49V002FA
Publication Release Date: February 19, 2002
- 3 -
Revision A2
FUNCTIONAL DESCRIPTION
Interface Mode Selection And Description
This device can be operated in two interface modes, one is Programmer interface mode, the other is
FWH interface mode. The IC pin of the device provides the control between these two interface
modes. These interface modes need to be configured before power up or return from #RESET
.
When
IC pin is set to high state, the device will be in the Programmer mode; while the IC pin is set to low
state (or leaved no connection), it will be in the FWH mode. In Programmer mode, this device just
behaves like traditional flash parts with 8 data lines. But the row and column address inputs are
multiplexed, which go through address inputs A[10:0]. For FWH mode, It complies with the FWH
Interface Specification. Through the FWH[3:0] to communicate with the system chipset .
Read (Write) Mode
In Programmer interface mode, the read (write) operation of the W49V002FA is controlled by #OE
(#WE). The #OE(#WE) is held low for the host to obtain(write) data from(to) the outputs(inputs). #OE
is the output control and is used to gate data from the output pins. The data bus is in high impedance
state when #OE is high. As for in the FWH interface mode, the read or write is determined by the "bit 0
& bit 1 of START CYCLE ". Refer to the FWH cycle definition for further details.
Reset Operation
The #RESET input pin can be used in some application. When #RESET pin is at high state, the device
is in normal operation mode. When #RESET pin is at low state, it will halt the device and all outputs will
be at high impedance state. As the high state re-asserted to the #RESET pin, the device will return to
read or standby mode, it depends on the control signals.
Chip Erase Operation
The chip-erase mode can be initiated by a six-byte command sequence. After the command loading
cycle, the device enters the internal chip erase mode, which is automatically timed and will be
completed within fast 150 mS (typical). The host system is not required to provide any control or timing
during this operation. If the boot block programming lockout is activated, only the data in the other
memory blocks will be erased to FF(hex) while the data in the boot block will not be erased (remains
as the same state before the chip erase operation). The entire memory array will be erased to FF(hex)
by the chip erase operation if the boot block programming lockout feature is not activated. The device
will automatically return to normal read mode after the erase operation completed. Data polling and/or
Toggle Bits can be used to detect end of erase cycle.
Sector Erase Operation
The seven sectors, one boot block and two parameter memory and four main blocks, can be erased
individually by initiating a six-byte command sequence. Sector address is latched on the falling #WE
edge of the sixth cycle, while the 30(hex) data input command is latched at the rising edge of #WE.
After the command loading cycle, the device enters the internal sector erase mode, which is
automatically timed and will be completed within fast 150 mS (typical). The host system is not required
to provide any control or timing during this operation. The device will automatically return to normal
read mode after the erase operation completed. Data polling and/or Toggle Bits can be used to detect
end of erase cycle.
相關PDF資料 |
PDF描述 |
|---|---|
| W49V002FAQ | 256K X 8 CMOS FLASH MEMORY WITH FWH INTERFACE |
| W503GDT | 5x5mm SQUARE TOP LED LAMP |
| W503IDT | 5x5mm SQUARE TOP LED LAMP |
| W503YDT | 5x5mm SQUARE TOP LED LAMP |
| W51-A122B1-7 | Thermal Circuit Breakers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W49V002FAQ | 制造商:WINBOND 制造商全稱:Winbond 功能描述:256K X 8 CMOS FLASH MEMORY WITH FWH INTERFACE |
| W49V002P | 制造商:WINBOND 制造商全稱:Winbond 功能描述:256K x 8CMOS FLASH MEMORY WITH LPC INTERFACE |
| W49V002T | 制造商:WINBOND 制造商全稱:Winbond 功能描述:256K x 8CMOS FLASH MEMORY WITH LPC INTERFACE |
| W4A-1205 | 制造商:BICC GENERAL CABLE INDUST 功能描述:MULTI CONDUCTORS |
| W4BD1804 (SEOW 18/4) | 制造商:COLEMAN CABLE 功能描述:WIRE 制造商:Coleman Cable Inc 功能描述:WIRE |
發布緊急采購，3分鐘左右您將得到回復。