- 您現在的位置：買賣IC網 > PDF目錄363889 > W49L201T-90 (WINBOND ELECTRONICS CORP) 256K X 8 CMOS FLASH MEMORY PDF資料下載
參數資料
| 型號： | W49L201T-90 |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | PROM |
| 英文描述： | 256K X 8 CMOS FLASH MEMORY |
| 中文描述： | 128K X 16 FLASH 3.3V PROM, 90 ns, PDSO48 |
| 封裝： | 12 X 20 MM, TSOP-48 |
| 文件頁數： | 3/23頁 |
| 文件大小： | 190K |
| 代理商： | W49L201T-90 |
Preliminary W49L201
Publication Release Date: May 2000
- 3 -
Revision A1
FUNCTIONAL DESCRIPTION
Read Mode
The read operation of the W49L201 is controlled by CE and OE, both of which have to be low for the
host to obtain data from the outputs.
CE
is used for device selection. When
CE
is high, the chip is
de-selected and only standby power will be consumed. OE is the output control and is used to gate
data to the output pins. The data bus is in high impedance state when either
CE
or
OE
is high. Refer
to the timing waveforms for further details.
Reset Operation
The RESET
input pin can be used in some application. When RESET pin is at high state, the device
is in normal operation mode. When RESET pin is driven low for at least a period of T
RP
, it will halts
the device and all outputs are at high impedance state. The device also resets the internal state
machine to read array data. The operation that was interrupted should be reinitiated once the device
is ready to accept another command sequence to assure data integrity. As the high state re-asserted
to the RESET pin, the device will return to read or standby mode, it depends on the control signals.
The system can read data T
RH
after the RESET
pin returns to V
IH
. The other function for RESET pin
is temporary reset the boot block. By applying the 12V to RESET pin, the boot block can be
reprogrammed even though the boot block lockout function is enabled.
Boot Block Operation
There is one 8K-word boot block in this device, which can be used to store boot code. It is located in
the first 8K words of the memory with the address range from 0000(hex) to 1FFF(hex).
See Command Codes for Boot Block Lockout Enable for the specific code. Once this feature is set
the data for the designated block cannot be erased or programmed (programming lockout); other
memory locations can be changed by the regular programming method.
There is one condition that the lockout feature can be overrides. Just apply 12V to RESET
pin, the
lockout feature will temporary be inactivated and the boot block can be erased/programmed. Once
the RESET pin returns to TTL level, the lockout feature will be activated again.
In order to detect whether the boot block feature is set on the 8K-words block, users can perform
software command sequence: enter the product identification mode (see Command Codes for
Identification/Boot Block Lockout Detection for specific code), and then read from address "0002
hex". If the output data in DQ0 is "1", the boot block programming lockout feature is activated; if the
output data in DQ0 is "0", the lockout feature is inactivated and the block can be erased/programmed.
To return to normal operation, perform a three-byte command sequence (or an alternate single-word
command) to exit the identification mode. For the specific code, see Command Codes for
Identification/Boot Block Lockout Detection.
Chip Erase Operation
The chip-erase mode can be initiated by a six-word command sequence. After the command loading
cycle, the device enters the internal chip erase mode, which is automatically timed and will be
completed in a fast 100 mS (typical). The host system is not required to provide any control or timing
相關PDF資料 |
PDF描述 |
|---|---|
| W49L201T-70 | 256K X 8 CMOS FLASH MEMORY |
| W49L201 | 128Kx16bit CMOS Flash Memory(128K×16位CMOS 閃速存儲器) |
| W49S201 | 128K×16bit CMOS Flash Memory With Synchronous Burst Read(具有同步脈沖讀模式的128K×16位CMOS閃速存儲器) |
| W49V002P | Zener Diode; Application: Low noise; Pd (mW): 250; Vz (V): 3.4 to 3.8; Condition Iz at Vz (mA): 0.5; C (pF) max: -; Condition VR at C (V):   ESD (kV) min: -; Package: MHD |
| W49V002T | Zener Diode; Application: Low noise; Pd (mW): 250; Vz (V): 3.7 to 4.1; Condition Iz at Vz (mA): 0.5; C (pF) max: -; Condition VR at C (V):   ESD (kV) min: -; Package: MHD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W49L401 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:FLASH |
| W49L401S-70B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:EEPROM |
| W49L401T-70B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:EEPROM |
| W49L401TS70B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:EEPROM |
| W49L401TT70B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:EEPROM |
發布緊急采購，3分鐘左右您將得到回復。