- 您現在的位置：買賣IC網 > PDF目錄363888 > W49F102P45 (WINBOND ELECTRONICS CORP) 64K X 16 CMOS FLASH MEMORY PDF資料下載
參數資料
| 型號： | W49F102P45 |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | PROM |
| 英文描述： | 64K X 16 CMOS FLASH MEMORY |
| 中文描述： | 64K X 16 FLASH 5V PROM, 45 ns, PQCC44 |
| 封裝： | PLASTIC, LCC-44 |
| 文件頁數： | 3/21頁 |
| 文件大小： | 277K |
| 代理商： | W49F102P45 |
W49F102
Publication Release Date: October 2000
- 3 -
Revision A3
FUNCTIONAL DESCRIPTION
Read Mode
The read operation of the W49F102 is controlled by CE and OE, both of which have to be low for
the host to obtain data from the outputs. CE is used for device selection. When CE is high, the
chip is de-selected and only standby power will be consumed. OE is the output control and is used
to gate data from the output pins. The data bus is in high impedance state when either CE or OE
is high. Refer to the timing waveforms for further details.
Boot Block Operation
There is one 8K-word boot block in this device, which can be used to store boot code. It is located in
the first 8K words of the memory with the address range from 0000 hex to 1FFF hex.
See Command Codes for Boot Block Lockout Enable for the specific code. Once this feature is set the
data for the designated block cannot be erased or programmed (programming lockout); other memory
locations can be changed by the regular programming method. Once the boot block programming
lockout feature is activated, the chip erase function will only affect the main memory.
In order to detect whether the boot block feature is set on the 8K-words block, users can perform
software command sequence: enter the product identification mode (see Command Codes for
Identification/Boot Block Lockout Detection for specific code), and then read from address "0002 hex".
If the output data is "FF hex," the boot block programming lockout feature is activated; if the output
data is "FE hex," the lockout feature is inactivated and the block can be erased/programmed.
To return to normal operation, perform a three-byte command sequence (or an alternate single-word
command) to exit the identification mode. For the specific code, see Command Codes for
Identification/Boot Block Lockout Detection.
Chip Erase Operation
The chip-erase mode can be initiated by a six-word command sequence. After the command loading
cycle, the device enters the internal chip erase mode, which is automatically timed and will be
completed in a fast 100 mS (typical). The host system is not required to provide any control or timing
during this operation. If the boot block programming lockout is activated, only the data in the main
memory will be erased to FF(hex), and the data in the boot block will not be erased (remains same as
before the chip erase operation). The entire memory array (main memory and boot block) will be
erased to FF(hex). by the chip erase operation if the boot block programming lockout feature is not
activated. The device will automatically return to normal read mode after the erase operation
completed. Data polling and/or Toggle Bits can be used to detect end of erase cycle.
Main Memory Erase Operation
The main memory erase mode can be initiated by a six-word command sequence. After the command
loading cycle, the device enters the internal main-memory erase mode, which is automatically timed
and will be completed in a fast 100 mS (typical). The host system is not required to provide any control
or timing during this operation. The device will automatically return to normal read mode after the erase
operation completed. Data polling and/or Toggle Bits can be used to detect end of erase cycle.
相關PDF資料 |
PDF描述 |
|---|---|
| W49F201S-45 | 128K X 16 CMOS FLASH MEMORY |
| W49F201S-45B | 5015 RR 5#16S SKT RECP |
| W49F201S-55 | 5015 RR 5#12 PIN RECP |
| W49F201S-55B | 5015 RR 5#12 PIN RECP |
| W49F201 | 128K×16bit CMOS Flash Memory(128K×16位CMOS閃速存儲器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W49F102P-45 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:EEPROM|FLASH|64KX16|CMOS|LDCC|44PIN|PLASTIC |
| W49F102Q40 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:64K X 16 CMOS FLASH MEMORY |
| W49F102Q45 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:64K X 16 CMOS FLASH MEMORY |
| W49F102Q-45 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:EEPROM|FLASH|64KX16|CMOS|TSSOP|40PIN|PLASTIC |
| W49F201 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:128K X 16 CMOS FLASH MEMORY |
發布緊急采購，3分鐘左右您將得到回復。