- 您現在的位置：買賣IC網 > PDF目錄363888 > W49F020P-70 (WINBOND ELECTRONICS CORP) 256K X 8 CMOS FLASH MEMORY PDF資料下載
參數資料
| 型號： | W49F020P-70 |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | PROM |
| 英文描述： | 256K X 8 CMOS FLASH MEMORY |
| 中文描述： | 256K X 8 FLASH 5V PROM, 70 ns, PQCC32 |
| 封裝： | PLASTIC, LCC-32 |
| 文件頁數： | 4/21頁 |
| 文件大小： | 190K |
| 代理商： | W49F020P-70 |
Preliminary W49F020
- 4 -
T
BP
) when completing programming and return to normal read mode. Data polling and/or Toggle Bits
can be used to detect end of program cycle.
Hardware Data Protection
The integrity of the data stored in the W49F020 is also hardware protected in the following ways:
(1) Noise/Glitch Protection: A WE pulse with less than 15 nS in duration will not initiate a write cycle.
(2) V
DD
Power Up/Down Detection: The programming operation is inhibited when V
DD
is less than
2.5V typical.
(3) Write Inhibit Mode: Forcing OE low, CE high, or WE high will inhibit the write operation. This
prevents inadvertent writes during power-up or power-down periods.
(4) V
DD
power-on delay: When V
DD
has reached its sense level, the device will automatically time-out
5 mS before any write (erase/program) operation.
Data Polling (DQ
7
)- Write Status Detection
The W49F020 features a data polling function which used to indicate the end of a program or erase
cycle. When the W49F020 is in the internal program or erase cycle, any attemption to read DQ
7
of the
last word loaded will receive the complement of the true data. Once the program or erase cycle is
completed, DQ
7
will show the true data. Note that DQ
7
will show logical "0" during the erase cycle, and
become logical "1" or true data when the erase cycle has been completed.
Toggle Bit (DQ
6
)- Write Status Detection
In addition to data polling, the W49F020 provides another method for determining the end of a program
cycle. During the internal program or erase cycle, any consecutive attempts to read DQ
6
will produce
alternating 0's and 1's. When the program or erase cycle is completed, this toggling between 0's and 1's
will stop. The device is then ready for the next operation.
Product Identification
The product ID operation outputs the manufacturer code and device code. Programming equipment
automatically matches the device with its proper erase and programming algorithms.
The manufacturer and device codes can be accessed by software or hardware operation. In software
access mode, a three-word (or JEDEC 3-word) command sequence can be used to access the product
ID. A read from address 0000H outputs the manufacturer code DA(hex); and a read from address
0001H outputs the device code 8C(hex) for W49F020. The product ID operation can be terminated by a
three-word command sequence or an alternated one-word command sequence (see Command
Definition table).
In the hardware access mode, access to the product ID will be activated by forcing CE and OE low,
WE
high, and raising A9 to 12 volts.
相關PDF資料 |
PDF描述 |
|---|---|
| W49F020P-70B | 256K X 8 CMOS FLASH MEMORY |
| W49F020P-90 | 256K X 8 CMOS FLASH MEMORY |
| W49F020P-90B | 256K X 8 CMOS FLASH MEMORY |
| W49F020-70 | Circular Connector; Body Material:Aluminum; Series:PT07; No. of Contacts:8; Connector Shell Size:12; Connecting Termination:Crimp; Circular Shell Style:Jam Nut Receptacle; Circular Contact Gender:Pin; Insert Arrangement:12-8 |
| W49F020Q-70B | 256K X 8 CMOS FLASH MEMORY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W49F020P-70B | 制造商:WINBOND 制造商全稱:Winbond 功能描述:256K X 8 CMOS FLASH MEMORY |
| W49F020P-90 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:256K X 8 CMOS FLASH MEMORY |
| W49F020P-90B | 制造商:WINBOND 制造商全稱:Winbond 功能描述:256K X 8 CMOS FLASH MEMORY |
| W49F020Q-70 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:256K X 8 CMOS FLASH MEMORY |
| W49F020Q-70B | 制造商:WINBOND 制造商全稱:Winbond 功能描述:256K X 8 CMOS FLASH MEMORY |
發布緊急采購，3分鐘左右您將得到回復。