国产精品成人VA在线观看-国产乱妇乱子视频在播放-国产日韩精品一区二区三区在线-国模精品一区二区三区

參數資料
型號: W45B012
廠商: WINBOND ELECTRONICS CORP
元件分類: FLASH
英文描述: 4 Mbit Uniform Sector, Serial Flash Memory
中文描述: 4兆位統一部門,串行閃存
文件頁數: 3/16頁
文件大小: 283K
代理商: W45B012
Preliminary W45B012
Publication Release Date: April 18, 2002
- 3 -
Revision A1
FUNCTIONAL DESCRIPTION
Device Operation
The W45B012 uses bus cycles of 8 bits each for commands, data, and addresses to execute
operations. The operation instructions are listed in the table below. All instructions are synchronized off
a high to low transition of #CE. The first low to high transition on SCK will initiate the instruction
sequence. Inputs will be accepted on the rising edge of SCK starting with the most significant bit. Any
low to high transition on #CE before the input instruction completes will terminate any instruction in
progress and return the device to the standby mode.
Read
The Read operation outputs the data in order from the initial accessed address. While SCK is input,
the address will be incremented automatically until end (top) of the address space, then the internal
address pointer automatically increments to beginning (bottom) of the address space (00000h), and
data out stream will continue. The read data stream is continuous through all addresses until
terminated by a low to high transition on #CE.
Sector/Chip-erase Operation
The Sector-Erase operation clears all bits in the selected sector to "FF". The Chip-Erase instruction
clears all bits in the device to "FF".
Byte-program Operation
The Byte-Program operation programs the bits in the selected byte to the desired data. The selected
byte must be in the erased state ("FF") when initiating a Program operation. The data is input from bit 7
to bit 0 in order.
Software Status Operation
The Status operation determines if an Erase or Program operation is in progress. If bit 0 is at a "0" an
Erase or Program operation is in progress, the device is busy. If bit 0 is at a "1" the device is ready for
any valid operation. The status read is continuous with ongoing clock cycles until terminated by a low
to high transition on #CE.
Reset
Reset will terminate any operation, e.g., Read, Erase and Program, in progress. It is activated by a
high to low transition on the #RESET pin. The device will remain in reset condition as long as #RESET
is low. Minimum reset time is 10
μ
S. See Figure 14 for reset timing diagram. #RESET is internally
pulled-up and could remain unconnected during normal operation. After reset, the device is in standby
mode, a high to low transition on #CE is required to start the next operation. An internal power-on reset
circuit protects against accidental data writes. Applying a logic level low to #RESET during the power-
on process then changing to a logic level high when V
DD
has reached the correct voltage level will
provide additional protection against accidental writes during power on.
Read WINBOND ID/Read Device ID
The Read Manufacturer ID and Read Device ID operations read the JEDEC assigned manufacturer
identification and the manufacturer assigned device identification codes. These codes may be used to
determine the actual device resident in the system.
相關PDF資料
PDF描述
W45B012P 4 Mbit Uniform Sector, Serial Flash Memory
W45B012Z 4 Mbit Uniform Sector, Serial Flash Memory
W45B512 4 Mbit Uniform Sector, Serial Flash Memory
W45NM60 N-CHANNEL 600V - 0.09ohm - 45A TO-247 MDmes TM Power MOSFET
W48C101-01 Spread Spectrum BX System Frequency Generator(寬頻譜BX系統頻率發生器)
相關代理商/技術參數
參數描述
W45B012P 制造商:WINBOND 制造商全稱:Winbond 功能描述:1M x 1 SERIAL FLASH MEMORY
W45B012Z 制造商:WINBOND 制造商全稱:Winbond 功能描述:1M x 1 SERIAL FLASH MEMORY
W45B512 制造商:WINBOND 制造商全稱:Winbond 功能描述:512k * 1 SERIAL FLASH
W45DUF35-1 制造商:Stancor 功能描述:
W45NM50 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:N-CHANNEL 550V Tjmax - 0.08ohm - 45A TO-247 MDmesh TM MOSFET