- 您現在的位置：買賣IC網 > PDF目錄363880 > W29EE01190B (WINBOND ELECTRONICS CORP) 128K X 8 CMOS FLASH MEMORY PDF資料下載
參數資料
| 型號： | W29EE01190B |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | PROM |
| 英文描述： | 128K X 8 CMOS FLASH MEMORY |
| 中文描述： | 128K X 8 FLASH 5V PROM, 90 ns, PDIP32 |
| 封裝： | 0.600 INCH, PLASTIC, DIP-32 |
| 文件頁數： | 4/20頁 |
| 文件大小： | 183K |
| 代理商： | W29EE01190B |
W29EE011
- 4 -
Hardware Data Protection
The integrity of the data stored in the W29EE011 is also hardware protected in the following ways:
(1) Noise/Glitch Protection: A WE pulse of less than 15 nS in duration will not initiate a write cycle.
(2) V
DD
Power Up/Down Detection: The programming operation is inhibited when V
DD
is less than
3.8V.
(3) Write Inhibit Mode: Forcing
OE
low,
CE
high, or
WE
high will inhibit the write operation. This
prevents inadvertent writes during power-up or power-down periods.
Data Polling (DQ
7
)-Write Status Detection
The W29EE011 includes a data polling feature to indicate the end of a programming cycle. When the
W29EE011 is in the internal programming cycle, any attempt to read DQ
7
of the last byte loaded
during the page/byte-load cycle will receive the complement of the true data. Once the programming
cycle is completed. DQ
7
will show the true data.
Toggle Bit (DQ
6
)-Write Status Detection
In addition to data polling, the W29EE011 provides another method for determining the end of a
program cycle. During the internal programming cycle, any consecutive attempts to read DQ
6
will
produce alternating 0's and 1's. When the programming cycle is completed, this toggling between 0's
and 1's will stop. The device is then ready for the next operation.
5-Volt-only Software Chip Erase
The chip-erase mode can be initiated by a six-byte command sequence. After the command loading
cycles, the device enters the internal chip erase mode, which is automatically timed and will be
completed in 50 mS. The host system is not required to provide any control or timing during this
operation.
Product Identification
The product ID operation outputs the manufacturer code and device code. Programming equipment
automatically matches the device with its proper erase and programming algorithms.
The manufacturer and device codes can be accessed by software or hardware operation. In the
software access mode, a six-byte command sequence can be used to access the product ID. A read
from address 0000H outputs the manufacturer code (DAh). A read from address 0001H outputs the
device code (C1h). The product ID operation can be terminated by a three-byte command sequence.
In the hardware access mode, access to the product ID is activated by forcing
CE
and
OE
low,
WE
high, and raising A9 to 12 volts.
相關PDF資料 |
PDF描述 |
|---|---|
| W29EE011P-90 | 128K X 8 CMOS FLASH MEMORY |
| W29EE011P15B | 128K X 8 CMOS FLASH MEMORY |
| W29EE011T-15 | KJA SERIES III |
| W29EE011T15B | 128K X 8 CMOS FLASH MEMORY |
| W29EE011-90 | HOOD DB37 PLASTIC 10 PACK |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W29EE011-90B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:EEPROM|FLASH|128KX8|CMOS|DIP|32PIN|PLASTIC |
| W29EE011-90N | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:EEPROM|FLASH|128KX8|CMOS|DIP|32PIN|PLASTIC |
| W29EE011P | 制造商:WINBOND 制造商全稱:Winbond 功能描述:128K X 8 CMOS FLASH MEMORY |
| W29EE011P-12 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 Flash EEPROM |
| W29EE011P-15 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:128K X 8 CMOS FLASH MEMORY |
發布緊急采購，3分鐘左右您將得到回復。