- 您現在的位置：買賣IC網 > PDF目錄363877 > W27L520S-70 (WINBOND ELECTRONICS CORP) 64K X 8 ELECTRICALLY ERASABLE EPROM PDF資料下載
參數資料
| 型號： | W27L520S-70 |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | PROM |
| 英文描述： | 64K X 8 ELECTRICALLY ERASABLE EPROM |
| 中文描述： | 64K X 8 EEPROM 3V, 70 ns, PDSO20 |
| 封裝： | 0.300 INCH, SOP-20 |
| 文件頁數： | 2/16頁 |
| 文件大小： | 105K |
| 代理商： | W27L520S-70 |
Preliminary W27L520
- 2 -
FUNCTIONAL DESCRIPTION
Read Mode
Unlike conventional UVEPROMs, which has CE and OE two control functions, the W27L520 has one
OE/V
PP
and one ALE (address_latch_enable) control functions. The ALE makes lower address A[7:0]
to be latched in the chip when it goes from high to low, so that the same bus can be used to output
data during read mode. i.e. lower address A[7:0] and data bus DQ[7:0] are multiplexed. OE/V
PP
controls the output buffer to gate data to the output pins. When addresses are stable, the address
access time (T
ACC
) is equal to the delay from ALE to output (T
CE
), and data are available at the
outputs T
OE
after the falling edge of OE/V
PP
, if T
ACC
and T
CE
timings are met.
Erase Mode
The erase operation is the only way to change data from "0" to "1." Unlike conventional UVEPROMs,
which use ultraviolet light to erase the contents of the entire chip (a procedure that requires up to half
an hour), the W27L520 uses electrical erasure. Generally, the chip can be erased within 100 mS by
using an EPROM writer with a special erase algorithm.
There are two ways to enter Erase mode. One is to raise OE/V
PP
to V
PE
(13V), V
DD
= V
DE
(6.5V), A9
= V
HH
(13V), A10 = high A8&A11 = low, and all other address pins include AD[7:0] keep at fixed low
or high. Pulsing ALE high starts the erase operation. The other way is somewhat like flash, by
programming two consecutive commands into the device and then enter Erase mode. The two
commands are loading Data = AA(hex) to Addr. = 5555(hex) and Data = 10(hex) to Addr. =
2AAA(hex). Be careful to note that the ALE pulse widths of these two commands are different: One is
50uS, while the other is 100mS. Please refer to the Smart Erase Algorithm 1 & 2.
Erase Verify Mode
The device will enter the Erase Verify Mode automatically after Erase Mode. Only power down the
device can force the device enter Normal Read Mode again.
Program Mode
Programming is the only way to change cell data from "1" to "0." The program mode is entered when
OE/V
PP
is raised to V
PP
(13V), V
DD
= V
DP
(6.5V), the address pins equal the desired addresses, and
the input pins equal the desired inputs. Pulsing ALE high starts the programming operation.
Program Verify Mode
The device will enter the Program Verify Mode automatically after Program Mode. Only power down
the device can force the device enter Normal Read Mode again.
Erase/Program Inhibit
Erase or program inhibit mode allows parallel erasing or programming of multiple chips with different
data. When ALE low, erasing or programming of non-target chips is inhibited, so that except for the
ALE and OE/V
PP
pins, the W27L520 may have common inputs.
Standby Mode
The standby mode significantly reduces V
DD
current. This mode is entered when ALE and OE/V
PP
keep high. In standby mode, all outputs are in a high impedance state.
System Considerations
相關PDF資料 |
PDF描述 |
|---|---|
| W27L520S-90 | 64K X 8 ELECTRICALLY ERASABLE EPROM |
| W27L520W-70 | 64K X 8 ELECTRICALLY ERASABLE EPROM |
| W27L520W-90 | 64K X 8 ELECTRICALLY ERASABLE EPROM |
| W27L520 | 64K×8bit Electrically Eresable EPROM(64K×8位電可擦除EPROM) |
| W28F641B | 64MBIT (4MBIT 】 16) PAGE MODE DUAL WORK FLASH MEMORY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W27L520S-90 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:64K X 8 ELECTRICALLY ERASABLE EPROM |
| W27L520W-70 | 制造商:Winbond Electronics Corp 功能描述:EEPROM, 64K x 8, 20 Pin, Plastic, TSSOP |
| W27L520W-90 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:64K X 8 ELECTRICALLY ERASABLE EPROM |
| W27LE520 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| W27LE520S-70 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:64K X 8 ELECTRICALLY ERASABLE EPROM |
發布緊急采購，3分鐘左右您將得到回復。