- 您現在的位置：買賣IC網 > PDF目錄373936 > AD8113 (Analog Devices, Inc.) Audio/Video 60 MHz 16 X 16, G = + 2 Crosspoint Switch PDF資料下載
參數資料
| 型號： | AD8113 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | Audio/Video 60 MHz 16 X 16, G = + 2 Crosspoint Switch |
| 中文描述： | 音頻/視頻60 MHz的16 × 16地下\u003d 2交叉點開關 |
| 文件頁數： | 18/28頁 |
| 文件大小： | 1391K |
| 代理商： | AD8113 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
REV. A
AD8113
–18–
Inputs and outputs should be preassigned to be either audio or
video. As described above, audio and video signals are treated
differently, so it is difficult to have the same AD8113 inputs or
outputs route audio or video signals in the same system at
different times. The various audio and video channels should
be configured as described in the above sections.
Video outputs that drive a terminated 75
transmission line
(150
equivalent load) will dissipate significantly more power
with
±
12 V supplies. An upper bound on power dissipation can
be approximated by the following method.
A video signal at the AD8113 output can have a maximum
value of 2 V. This is quite conservative, because most video
signals are about 700 mV peak at unity gain or 1.4 V peak after
a gain-of-two. A video signal only reaches this level when the video
content is at peak white, so this value is even more pessimistic.
Finally, a video signal will generally have some kind of sync and
blanking interval where its amplitude will be either 0 V (or black)
or very close to this level. The power dissipation will be much
lower during this period and this will occur at a very regular
duty cycle.
If the full 2 V signal is assumed to be present at 100% duty
cycle at the output, then the current in the output is 2 V/150
= 13.3 mA. If the positive supply is at 12 V, there will be a
10 V drop in the AD8113 output stage from the supply to the
output. This yields a power dissipated in the output of 133 mW
from one video load when running on supplies of
±
12 V. This
is by far a worst-case situation, and this power dissipation fac-
tor can be adjusted lower by adjusting for actual video levels,
sync-interval duty cycle, and average picture level considerations.
If too much power will be dissipated in this type of configuration,
it is possible to lower it by buffering the output. An AD8113
video output drives a divide-by-two resistive divider that is
made up of two 1 k
resistors. This presents a total load of
2 k
to the AD8113 outputs, which significantly reduces the
power dissipation. Refer to Figure 10.
AD8057
–
3
2
1k
1k
7
4
6
+5V
–5V
0.1 F
10 F
+
75
75
TRANSMISSION
LINE
75
75
TYPICAL
INPUT
AD8113
G = 2
+12V
–12V
1k
1k
0.1 F
10 F
TYPICAL
OUTPUT
+
+
Figure 10. Video Buffer Circuit
After this divider, the signal is now at a unity level because of
the channel gain of the AD8113 and the attenuation of the
divider. An AD8057 is configured as a gain-of-two buffer to
drive the terminated transmission line. The AD8058 is a dual
version of the AD8057.
The maximum supply voltage of the AD8057 is only about
±
6 V. If the only system supplies that are available are
±
12 V, a
higher voltage video op amp can be substituted for the AD8057.
Good candidates are the AD817 and AD818 or, if dual op amps
are needed, the AD826 and AD828.
CREATING LARGER CROSSPOINT ARRAYS
The AD8113 is a high density building block for creating cross-
point arrays of dimensions larger than 16
×
16. Various features,
such as output disable and chip enable, are useful for creating
larger arrays.
The first consideration in constructing a larger crosspoint is to
determine the minimum number of devices required. The 16
×
16
architecture of the AD8113 contains 256 points, which is a
factor of 64 greater than a 4
×
1 crosspoint (or multiplexer). The
PC board area, power consumption, and design effort savings are
readily apparent when compared to using these smaller devices.
For a nonblocking crosspoint, the number of points required is
the product of the number of inputs multiplied by the number
of outputs. Nonblocking requires that the programming of a given
input to one or more outputs does not restrict the availability of
that input to be a source for any other outputs.
Some nonblocking crosspoint architectures will require more than
this minimum as calculated above. Also, there are blocking archi-
tectures that can be constructed with fewer devices than this
minimum. These systems have connectivity available on a statis-
tical basis that is determined when designing the overall system.
The basic concept in constructing larger crosspoint arrays is
to connect inputs in parallel in a horizontal direction and to
wire-OR the outputs together in the vertical direction. The
meaning of horizontal and vertical can best be understood by
looking at a diagram. Figure 11 illustrates this concept for a
32
×
32 crosspoint array that uses four AD8113s.
1k
AD8113
AD8113
IN 00–15
IN 16–31
AD8113
AD8113
1k
1k
1k
16
16
16
16
16
16
16
16
16
16
Figure 11. 32
×
32 Audio Crosspoint Array Using Four
AD8113s
The inputs are individually assigned to each of the 32 inputs of
the two devices and a divider is used to normalize the channel
gain. The outputs are wire-ORed together in pairs. The output
from only one of a wire-ORed pair should be enabled at any
given time. The device programming software must be properly
written to cause this to happen.
Using additional crosspoint devices in the design can lower the
number of outputs that have to be wire-ORed together. Figure 12
shows a block diagram of a system using ten AD8113s to create
a nonblocking, gain-of-two, 128
×
16 crosspoint that restricts
the wire-ORing at the output to only four outputs.
Additionally, by using the lower eight outputs from each of the
two Rank 2 AD8113s, a blocking 128
×
32 crosspoint array can be
realized. There are, however, some drawbacks to this technique.
The offset voltages of the various cascaded devices will accumu-
相關PDF資料 |
PDF描述 |
|---|---|
| AD8113JST | Audio/Video 60 MHz 16 X 16, G = + 2 Crosspoint Switch |
| AD8115AST | Low Cost 225 MHz 16 X 16 Crosspoint Switches |
| AD8114-EB | Low Cost 225 MHz 16 X 16 Crosspoint Switches |
| AD8115-EB | Low Cost 225 MHz 16 X 16 Crosspoint Switches |
| AD8114 | ECONOLINE: REC2.2-S_DRW(Z)/H* - 2.2W DIP Package- 1kVDC Isolation- Regulated Output- 4.5-9V, 9-18V, 18-36V, 36-72V Wide Input Range 2 : 1- UL94V-0 Package Material- Continuous Short Circiut Protection- Cost Effective- 100% Burned In- Efficiency to 84% |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8113-EVAL | 制造商:Analog Devices 功能描述:AD8113 EVALUATION BOARD - Bulk |
| AD8113JST | 制造商:Analog Devices 功能描述:Analog Audio/Video Crosspoint 60MHz 16 x 16 100-Pin LQFP 制造商:Rochester Electronics LLC 功能描述:LQFP 40MHZ 16X16 G=+2 CROSSPOINT SWITCH - Bulk 制造商:Analog Devices 功能描述:Multiplexer IC Number of Channels:32 |
| AD8113JSTZ | 功能描述:IC VIDEO CROSSPOINT SWIT 100LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 特色產品:MicroPak? 標準包裝:1 系列:- 功能:開關 電路:2 x SPST - NC 導通狀態電阻:500 毫歐 電壓電源:單電源 電壓 - 電源，單路/雙路(±):1.4 V ~ 4.3 V 電流 - 電源:150nA 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-XFDFN 供應商設備封裝:8-XSON，SOT833-1 （1.95x1） 包裝:Digi-Reel® 其它名稱:568-5557-6 |
| AD8114 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Cost 225 MHz 16 X 16 Crosspoint Switches |
| AD8114_05 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Cost 225 MHz 16 ?? 16 Crosspoint Switches |
發布緊急采購，3分鐘左右您將得到回復。